Version 3 by Mahmoud Al-Qudsi
on Dec 13, 2006 20:27.

<< Changes from 2 to 3
compared with
Current by Mahmoud Al-Qudsi
on Oct 21, 2007 21:11.
(show comment)
 
Key
These lines were removed. This word was removed.
These lines were added. This word was added.

View page history


There are 10 changes. View first change.

 h1. Adding Windows Vista & Longhorn Server
  
  
 h2. Supported Systems
  
Every version of EasyBCD to date has had complete support for all versions of Windows Vista & Longhorn Server. EasyBCD was originally created as a Windows Vista-specific bootloader management tool, and quickly evolved and became the single most-versatile bootloader on the planet. As of EasyBCD 1.51, it has been verified to work with the following Vista systems:
  Every version of EasyBCD to date has had complete support for all versions of Windows Vista & Longhorn Server. EasyBCD was originally created as a Windows Vista-specific bootloader management tool, and quickly evolved into the single most-versatile bootloader on the planet. As of EasyBCD 1.7, it has been verified to work with the following Vista-based systems:
 * Windows Vista RTM
* Windows Vista SP1 Beta
 * Windows Vista Beta Builds 5086\+
 * Longhorn Server Beta 1\+
* Windows Vista 5086\+
  
It hasn't been tested with earlier versions, but EasyBCD should boot into them all just as well.
  It hasn't been tested with earlier Longhorn builds, but theoretically speaking EasyBCD should support anything from 4074 upwards - either via NTLDR or the BCD.
  
h2. Adding a Vista Entry
  
Adding a Windows Vista or Longhorn Server entry is a straight-forward process, and can be done from any operating system. Assuming you already have a fully-working BCD setup (i.e. EasyBCD runs OK, and changes can be seen):
  h2. Adding a Windows Vista Entry
  
 Adding a Windows Vista or Longhorn Server entry is a straight-forward process, and can be done from any of the [supported host operating systems|Supported Operating Systems]. Assuming you already have a fully-working BCD setup (i.e. EasyBCD runs OK and doesn't give you any errors on startup):
 # Run EasyBCD, go to the "Add/Remove Entries" screen
 # Enter the name you'd like to associate with the entry you're about to create in the "Name" box. For instance, "My Vista RTM Install"
# In the drive box, enter the letter of the drive followed by a colon (e.g. "C:"). It's important to note that the Drive Letter must be the one *currently visible in My Computer* that points to the drive that Vista or Longhorn Server is installed on. Even if the drive letters change from install to install, use the drive letters _as they appear in your current boot_. EasyBCD will automatically convert them to the proper drive & partition numbers.
 # Press the "Add Entry" button, and wait for the audible notification telling you everything went OK.
  # Select the letter of the drive/partition Windows Vista is installed on from the drop-down menu (e.g. "C:"). It's important to note that the Drive Letter must be the one *currently visible in My Computer* that points to the drive that Vista or Longhorn Server is installed on. Even if the drive letters change from install to install, use the drive letters _as they appear in your current boot_. EasyBCD will automatically convert them to the proper drive & partition numbers that can be understood by the Vista bootloader.
 # Press the "Add Entry" button, and wait for the notification telling you everything went OK.
 # The operating systems list should immediately change to reflect the new changes, and you're all set.
# *Optional:* Go to the "Change Settings" page or the "Advanced Options" and customize the options available for this entry.
  
 h2. Troubleshooting
  
 If you added a Windows Vista or Longhorn Server entry, and it fails to boot, you might want to check the following before asking for support.
 # *Did you specify the correct drive letter?*
 Make sure you entered the letter for the Vista partition as it is currently assigned in the operating system you're running EasyBCD from. That's usually the most common reason why Vista won't boot. To change the drive letter, see the instructions at [Changing the Drive Letter|Configuring the Bootloader#Changing the Drive Letter|Configuring the Bootloader#Changing the Drive Letter].
  Make sure you entered the letter for the Vista partition as it is currently assigned in the operating system you're running EasyBCD from. That's usually the most common reason why Vista won't boot. To change the drive letter, see the instructions at [Changing the Drive Letter|Configuring the Bootloader#Changing the Drive Letter|Configuring the Bootloader#Changing the Drive Letter] or delete the old entry and create a new one.
 # *Do you get a "Corrupt or Missing File" message on attempting to boot the newly created partition?*
 Verify that the drive letter specified points to a valid Windows Vista install.